If the engine is warm, this only lasts a few seconds. To get the slave cylinder throw into the accepted range, adjust the clutch plate until the indicator is in the operat- ing range again. Check that there is no play in ball joints and bushings. We recommend washing the chassis in conjunction with annual service when the entire vehicle is inspected in order to facilitate inspection and repair during the servicing. The bearing should normally be preloaded so there should not be any noticeable play in the bearings.
Check that the sealing strips are in good condition and secured. Danger: Indicates an unsafe practice where serious personal injury or death could occur. Vehicles and components produced after the above date may therefore have different specifications and repair methods. Note: Note on the report if carbon deposits are present in the air drier housing. Apply the retarder 5 times at position 2 for about 5 seconds each time. The belt must be changed if there is any cracking. To perform a check of the Sealing on the Rear Axle and Hub Reduction Gear complete the following: On the Rear Axle, inspect around the mating sur- faces for leaks past the gasket.
Check that the rubber boots on ball joints on the track rods, link rods, steering rods, extra hydraulic cylinder and the master and centring cylinder for the hydraulically steered pusher axle or trailing wheel axle are intact and seal correctly. Check the position of the door stop and adjust if necessary. Note: A cracked or damaged rubber boot means that the ball joint wears out quickly. Remove the outer casing 1 , radiator 2 and strainer 3. Hubs with bearings should therefore be replaced to avoid damage to the bearings.
T1007724 74 Group 17 Annual service Annual service 95 Check brake lever travel 1 The function of the automatic adjustment mechanism is checked by measuring the brake lever travel C. Adjust each Check valve clearance and injector adjustment. T1007386 79 Check exhaust pipe and silencer or particulate filter 1 Note: Vehicle equipped with particulate filter: If, depending on the service interval of the particulate filter, the filter is to be cleaned, see Additional measures, op. Note: Note the brake lining thickness in the report! In regular over-the-road operations the T-Ride should follow the normal lubrication schedule. The oil level must be between the markings on the oil reservoir. If vehicle is equipped with a pneumatic 5th wheel sliding release, operate release mechanism while listening through door or have a helper check the function.
We have over lots of customer reviews on Volvo Repair Manual to help you find exactly what you need. Check the oil level on the dipstick. All warning and control lamps should then be illuminated. Put the starter key in the 0 position. Slightly greater travel can occur without there being anything wrong with the automatic adjuster. Maximum permitted axial play is 2 mm. At the same time, measure accurately the distance between the support and the tyre.
The front of the vehicle should be supported on pallets and the parking brake must not be applied. Note: If, depending on change interval for the radiator, the radiator is to be replaced, see Additional procedures, op no. It covers every single detail on your car. The pneumatic system must be charged. Check that the hoses and pipes between the engine and intercooler are undamaged and are not chafed.
The filling vessels must be absolutely clean and must not contain any traces of dirt or any type of mineral based grease or oil. If any wear marks are found, note them. Fit the new filter and assemble the filter retainer. Service procedures which do not include an operation number in the title are for general information and no reference is made to V. An alternative to filling the system by starting the engine can be to use a pressure booster 9810621 If the pneumatic system is charged from an external source of compressed air, it should be done through the air drier charging nipple to prevent moisture entering the pneumatic system. Use only Volvo approved concentrated coolant, which contains special corrosion inhibitors and is adapted to Volvo engines. Blockage can cause extreme pressure in the axle and create leaks.
The joints should not have any slack. Check if the spring cradle 6×4, 6×6 and 8×4 shows any sign of wear in the bearing. Group 17 Annual service Annual service 40 Check fuel tank ventilation filter 1 This filter is installed on certain markets. Volvo Truck Corporation Göteborg, Sweden 20 044871 English 0000. Clean around the drain plug.